Since you guys are esentially the market for these cars, what is my car worth both modded & if it was returned to stock?
Teal 93 Cobra #3463
Just over 30K miles
Gray cloth interior
Body/paint is 9 out of 10. Some minor imperfections from door-dings that can be pulled out easily from the boys that do paintless dent removal. Clear coat in the hatch area is thin (I heard that was a problem on these cars). A few minor paint dings in the hood that have been filled in, color sanded, & buffed out, but you can still see a difference in paint due to the metalic in the Teal.
Interior is also 9 out of 10. Previous owner drilled a hole in the dash when he installed an MSD BTM & tachy 3 pod dash mounted gauge thing. Luckily these parts are easy to find from GT/LX stock. The driver side stock Cobra floor mat also has a rip at the top of the seam where the clutch pedal hits. Driver side power seat is also *slow*. Again, luckily it's the same as a GT part. Just haven't picked up a new one since I can't find the motors by themselves & I don't want to install a used POS.
Carpet has also been cut for the bolt-in roll cage. Stock Stereo was removed (Factory CD) from previous owner. I have a stock 93 Cobra stereo that I just haven't put back into the car. Those things are HARD to find!
Major mods:
Dart 8.2 deck Iron Eagle block
333ci rotating assembly built for 1000hp with 2618 forged pistons, taper-wall tool steel wrist pins, 24cc dished pistons (8.5:1 compression), Forged/nitrided Scat crankshaft (shot-peened, performance ground & polished), 4340 Forged 'I' beam rods with ARP2000 cap-screw bolts. ARP splayed main bolts. 4-bolts on all 5 main caps.
Vic Jr heads with chamber work only. Comp 953 Valvesprings, Titanium retainers, Comp spring cups, 10 degree superlocks, Custom .125" *thick wall* 5/16th pushrods, Comp Pro-magnum 1.6 rocker arms with 7/16th rocker studs. Valvetrain good for 25+psi & 7500RPM.
Link-bar hydraulic lifters setup at .006" preload
FMS *Cobra* valve covers w/stock gaskets.
Cometic MLS head gaskets
F303 camshaft installed on 113ICL
Billet steel 9 position timing chain
Stock Cobra intake mainfold, cut, ported, welded, & powdercoated
70MM Edelbrock TB
Flowmaster 3" full off-road exhaust (from shorties to tail pipe) with Dynomax 'Ultraflow' mufflers (not flowmaster POS's)
Auto Conversion done correctly (auto pedal assembly & wiring harness)
JW 'Ultra Bell' Professionally aligned to the crank centerline
JW 'Ultra Wheel'
Custom 10" torque converter
2500HP capable TH400 transmission with 17 roller bearings & *lightened* rotating assembly.
AJE custom Transmission cross member (bolt-in to stock location)
Custom Speedometer setup so stock speedo works & is correctly calibrated.
Custom 1000+HP capable steel driveshaft with 1350 Spicer U-joints
Welded stock 8.8 with 2.73 gears, spool, 31 spline Custom Mosier axles & Mosier c-clip eliminators. New stock Rear rotors (not installed).
Weight jacker lower control arms w/spherical bushings
Stock upper control arms (welded) with spherical bushings in rear end housing.
Upper & lower TQ box reinforcements
Strange Adjustable shocks & struts (10-way)
Stock springs front/rear
Subframe connectors
6-point Chromoly bolt-in Wolfe Racecraft cage
Safecraft 6-point harnes
B&M Hammer shifter cut/modified to fit under stock 5spd leather boot. No console modifications done.
A-pillar guage pod w/boost & fuel pressure
Ricks Custom Hot-Rod 'alumistealth' billet aluminum fuel tank/cell. 15gallons w/A1000 mounted Inside tank. Tank was insulated to absorbe fuel pump noise. No louder than stock inside vehicle.
Custom fuel system w/-6an lines, dual fuel filters (before & after pump), Pro-M billet aluminum fuel rails (1/2"), 50lb injectors, Areomotive FPR.
4-lug Baer 13" front brake kit with aluminum hubs, Aluminum hatted rotors, PBR calipers, stainless steel brake lines, & rebuilt stock brake booster.
Incon 800TT kit with the following modifications:
Fully ported exhaust manifolds, then ceramic coated.
Rebuilt ball-bearing turbos from Majestic in Dallas 1K miles ago
-8an teflon oil return lines
-4an teflon oil feed lines
-6an teflon water lines
Spearco 1000hp intercooler mounted under radiator. Greddy 'race' BOV mounted on intercooler for better tuning control.
14psi wastegate actuators
Pro-M calibrated 80MM mass-air
Custom Tuned with PMS.
Runs 104 octane with 16psi & 27 degrees total timing. This is to avoid any excessive valveguide wear, and prolong the life of the iron exhaust manifolds. (Most common form of failure for these manifolds is due to excessively retarded ignition timing which makes them glow red-hot).
Car weighs 3750lbs race weight in street trim & runs 10.4's @137mph.
Weighs 3650lbs race weight in race trim (slicks/skinnies) & last time out ran 10.25 @140.3mph.
The car needs a better suspenssion to 'hook'.....& it'll easily go 9's.
Although I own a dyno, she is not dynotuned. (non-load bearing dyno) She is tuned at the dragstrip. ET/MPH to weight put power at right around 800FWHP.
The only accessory removed from the car is the smog pump.
Car passes CA smog when stock H-pipe is bolted up & smog pump is installed.
There's a LOT more in the details of this car.
I am an engine builder & tuner by trade. The car was done right.
She drives damn-near stock on the street, has working PS, AC, etc. It's as close to 'super cobra' status as I can make it. Or at least my own idea of what a 'super cobra' would be if ever there was one.
I've owned the car since late 2001. 3rd owner.
Here are a crap-load of pics:


















